Falls are mostly caused by the: Consequences of the accidents from portable ladders include disabling injuries and fatalities. 1675 (b) Design and construction of portable ladders shall comply with T8 CCR 3276 (c). OSHA Ladder Safety Compliance: General Ladder Rules & Requirements, understands the environmental hazards nearby, Ladder rungs, steps, and cleats are parallel, level, and uniformly spaced when the ladder is in position for use, Ladders are used only for the purposes for which they were designed, Each employee faces the ladder when climbing up or down it, Each employee uses at least one hand to grasp the ladder when climbing up and down, No employee carries any object or load that could cause them to lose balance and fall while climbing up or down, Do not load ladders beyond their maximum intended load nor beyond their manufacturers rated capacity. Ladder rungs, steps, and cleats are parallel, level, and uniformly spaced when the ladder is in position for use; Ladder rungs, steps, and cleats are spaced not less than 10 inches (25 cm) and not more than 14 inches (36 cm) apart, as measured between the centerlines of the rungs, cleats, and steps, except that: Ladder rungs and steps in elevator shafts must be spaced not less than 6 inches (15 cm) apart and not more than 16.5 inches (42 cm) apart, as measured along the ladder side rails; and. The rungs and steps of portable metal ladders shall be corrugated, knurled, dimpled, coated with skid-resistant material, or otherwise treated to minimize slipping. Inspect the Ladder Before Every Use. Slide-Step Fixed Ladder Sections. GARLOCK SAFETY SYSTEMS 301371. Ladder Safety American Ladder Institute Despite its popularity among ladder users, metal cannot be used for all processes that need to reach reasonable heights. Accidents from portable ladders are very common. The ladder assembly would need to be judged on a case-by-case basis to determine if it would be considered a fixed ladder and if fall protection is needed. The U.S. Occupational Safety and Health Administration requires employers to provide ladders under a number of various workplace conditions. When unavoidable obstructions are encountered, the minimum perpendicular clearance between the centerline of fixed ladder rungs, cleats, and steps, and the obstruction on the climbing side of the ladder may be reduced to 24 inches (61 cm), provided that a deflection device is installed to guide employees around the obstruction. Also, inspect ladders for defects such as missing components, cracks, frayed ropes, corrosion or other problems . Ladders shall not be moved, shifted, or extended while occupied. The employer shall direct that ladders shall be placed so that employees climbing are not exposed to injury from projecting objects or doors that open toward the ladder. Statistics show that workers are more likely to abuse and misuse ladders rather than use them correctly in the workplace. Mobile ladder stands and platforms must be slip-resistant and capable of supporting four times their max load. When that is not possible, the ladder must be secured and a grasping device such as a grab rail must be provided. OSHA and ANSI Ladder Requirements. While the victim was carrying the ladder upright to the van, the foreman and several co-workers verbally warned him about the overhead power line. 10-14 IN (25-36 CM) On Center. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. Such a determination would have to be made on a case-by-case basis, per inspection. (OSHA FS 3660 - 2013) (English: PDF ) Ladder Safety: Reducing Falls in Construction: Safe Use of Job-made Wooden Ladders Fact Sheet (OSHA FS 3661 - 2013) (English: PDF ) Ladder Safety: Reducing Falls in Construction: Safe Use of Stepladders Fact Sheet (OSHA 3662 - 2013) (English: PDF ) Working Safely with Mobile Ladder Stands Ladders shall be fitted with slip-resistant bases and secured at top or bottom to prevent the ladder from slipping. Ladders shall be securely positioned on a level and firm base. The employer must ensure: Ladders are not loaded beyond the maximum intended load; Note to paragraph (c)(3): Essential ToolsContinue, There is no question that ladders are incredibly useful tools. Rungs and steps of portable metal ladders are corrugated, knurled, dimpled, coated with skid-resistant material, or otherwise treated to minimize the possibility of slipping; Each stepladder or combination ladder used in a stepladder mode is equipped with a metal spreader or locking device that securely holds the front and back sections in an open position while the ladder is in use; Ladders are used only on stable and level surfaces unless they are secured or stabilized to prevent accidental displacement; No portable single rail ladders are used; No ladder is moved, shifted, or extended while an employee is on it; Ladders placed in locations such as passageways, doorways, or driveways where they can be displaced by other activities or traffic: Are secured to prevent accidental displacement; or. This website uses cookies to improve your experience while you navigate through the website. The standing area of mobile ladder stands is within the base frame. 1. But, the more often a ladder is used, the higher chance there is for a fall or accident to occur. - Look for overhead power lines before handling a ladder. 16 IN (41 CM) Min Clearance between side rails. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. Most ladder accidents can be eliminated if the userunderstands the environmental hazards nearby. Do not store portable ladders where they are exposed to rain, mist, steam, or other sources of moisture. Ladders shall be capable of supporting the following loads without failure: Each self-supporting portable ladder: At least four times the maximum intended load, except that each extra-heavy-duty type 1A metal or plastic ladder shall sustain at least 3.3 times the maximum intended load. ANSI ASC A14.2-2017 provides recommendations for the spacing between rungs, angle of inclination, and the correct workmanship for the bolts, rivets, and welds that are holding the pieces of the ladder together. The tallest man who ever lived in recorded history, Robert Pershing Wadlow, stood at 811. This letter constitutes OSHA's interpretation of the requirements discussed. That's a bad assumption. , the average female height is 53.5 and the average male height is 59, Archaeologists have confirmed that ladders date back to at least 10,000 years ago, The most common material used in the construction of ladders is aluminum, ANSI ASC A14.2-2017: Ladders Portable Metal Safety Requirements, Youve Reached the Top, Now Stop and Think About Continued Ladder Safety, Dont Ignore These Basic Rules of Ladder Climbing, The Steps to Take Before Stepping Onto a Ladder for the First Time. Ladders shall have nonconductive siderails if they are used where the employee or the ladder could contact exposed energized electrical equipment, except as provided in 1926.955(b) and (c) of this part. Humans have always been constricted to the ground by our relatively-unchanged biological limitations. Don't step on chairs, boxes, bins, or other objects. Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. Prevention requires proper planning, correct ladder selection, Some of the more common hazards involving ladders, such as instability, electrical shock, and falls, can be predicted and prevented. Ladders shall be maintained free of oil, grease, and other slipping hazards. Cages for fixed ladders shall conform to all of the following: Horizontal bands shall be fastened to the side rails of rail ladders, or directly to the structure, building, or equipment for individual-rung ladders; Vertical bars shall be on the inside of the horizontal bands and shall be fastened to them; Cages shall extend not less than 27 inches (68 cm), or more than 30 inches (76 cm) from the centerline of the step or rung (excluding the flare at the bottom of the cage), and shall not be less than 27 inches (68 cm) in width; The inside of the cage shall be clear of projections; Horizontal bands shall be spaced not more than 4 feet (1.2 m) on center vertically; Vertical bars shall be spaced at intervals not more than 9 1/2 inches (24 cm) on center horizontally; The bottom of the cage shall be at a level not less than 7 feet (2.1 m) nor more than 8 feet (2.4 m) above the point of access to the bottom of the ladder. [Reply #1 (General Industry):] 29 CFR 1910.21(e)(2) defines fixed ladders as "a ladder permanently attached to a structure, building, or equipment." Where the total length of a climb equals or exceeds 24 feet (7.3 m), fixed ladders shall be equipped with one of the following: Self-retracting lifelines, and rest platforms at intervals not to exceed 150 feet (45.7 m); or. The following statistics and real stories demonstrate the severity of accidents from ladders: A 59-year-old painter/independent contractor died of injuries after he fell while working from a metal extension ladder. good work procedures and adequate ladder maintenance. These are some examples of topics that might be covered in a ladder or stairway training: OSHA does require employers to retrain each employee as necessary to maintain their understanding and knowledge on the safe use and construction of ladders and stairs. Position Ladders Correctly Before you position your portable ladder, make sure there are no hazards above. Since we were never meant to leave the ground, very strict precautions should be taken for the structure of ladders. Except when portable ladders are used to gain access to fixed ladders (such as those on utility towers, billboards, and other structures where the bottom of the fixed ladder is elevated to limit access), when two or more separate ladders are used to reach an elevated work area, the ladders shall be offset with a platform or landing between the ladders. General Requirements, Portable Ladders, Fixed Ladders, Mobile Ladder Stands. 1910.23(b)(5) Wooden ladders are not coated with any material that may obscure structural defects. [Question #2:] Stacked and scaling ladders must have fall protection over a certain height, even if they are physically removable by crane and even though they are less than 20 ft length in individual piece length (and never joined), and when they are positioned vertically (or steeper than 4:1 angle)? Are guarded by a temporary barricade, such as a row of traffic cones or caution tape, to keep the activities or traffic away from the ladder; The cap (if equipped) and top step of a stepladder are not used as steps; Portable ladders used on slippery surfaces are secured and stabilized; The top of a non-self-supporting ladder is placed so that both side rails are supported, unless the ladder is equipped with a single support attachment; Portable ladders used to gain access to an upper landing surface have side rails that extend at least 3 feet (0.9 m) above the upper landing surface (see Figure D-1 of this section); Ladders and ladder sections are not tied or fastened together to provide added length unless they are specifically designed for such use; Fixed ladders are capable of supporting their maximum intended load; The minimum perpendicular distance from the centerline of the steps or rungs, or grab bars, or both, to the nearest permanent object in back of the ladder is 7 inches (18 cm), except for elevator pit ladders, which have a minimum perpendicular distance of 4.5 inches (11 cm); Grab bars do not protrude on the climbing side beyond the rungs of the ladder that they serve; For through ladders, the steps or rungs are omitted from the extensions, and the side rails are flared to provide not less than 24 inches (61cm) and not more than 30 inches (76 cm) of clearance. ANSI ASC A14.2-2007: Portable Metal Ladder Safety Requirements. OSHA Hard Hat Requirements for 2023 | New Hard Hat Safety Rules, OSHA Violations, Citations, and Fines List for 2023, Winter Weather Safety Tips for Construction Site Workers, HAZWOPER Training 101: OSHA Standard Requirements and Benefits, OSHA Welding Safety Guidelines and Checklist, OSHA Flammable Storage Regulations Cabinets, Liquids, & More, 5 Important OSHA Ladder Safety Standards & Rules, What Is Management of Change (MOC)? In the configurations in which they are used, portable platforms shall be capable of supporting without failure at least 2.5 times the maximum intended load. Did you know that 20% of lost work-day and fatal workplace injuries are caused by ladder falls in general industry? Workers not being trained adequately on ladder safety, Improper selection, care or use including incorrect positioning, Using the wrong ladder for the specific job. Learn how your comment data is processed. Application. The following OSHA ladder inspection requirements are specified in their safety standards. Your email address will not be published. 42 IN (107 CM) Min. Ladder rungs, steps, and cleats have a minimum width of 11.5 inches (29 cm) on portable ladders and 16 inches (41 cm) for fixed ladders Wooden ladders are not coated with any material that may obscure structural defects Metal ladders are made with corrosion-resistant material or protected against corrosion Individual sections from different multi-sectional ladders or two or more single straight ladders shall not be tied or fastened together to achieve additional length. If it is a fixed ladder, it will depend upon the conditions specified in the standard, i.e., is the climber a "qualified climber"? Ladder rungs, steps, and cleats are spaced not less than 10 and not more than 14 apartmeasured between the centerlines of the rungs, cleats, and steps, except: Ladder rungs and steps in elevator shafts must be spaces not less than 6 apart and not more than 16.5 apartmeasured along the side rails, Fixed ladder rungs and steps on telecommunication towers must be spaced no more than 18 apartmeasured between the centerlines of the rungs or steps, Steps on stepstools are spaced not less than 8 apart and not more than 12 apartmeasured between the centerlines of the steps. ANSI ASC A14.5-2017: Ladders - Portable Reinforced Plastic - Safety Requirements is available on the ANSI Webstore. The OSHA Ladder Inspection Checklists covers all ladders and its general requirements. Rungs, cleats, and steps of the base section of extension trestle ladders shall not be less than 8 inches (20 cm) nor more than 18 inches (46 cm) apart, as measured between center lines of the rungs, cleats, and steps. [Reply #4 (General Industry):] Again, if the ladder in question is a portable ladder, there is no requirement for fall protection. victim picked up a metal ladder to carry it to the work van. 1910.23 (b) General requirements for all ladders. Ladders shall be inspected by a competent person for visible defects on a periodic basis and after any occurrence that could affect their safe use. Avoid electrical hazards! OSHA requirements are set by statute, standards and regulations. 1926.1053(a)(3)(ii) The ladder slid down, and the employee fell to the floor, sustaining fatal injuries. Many times, avoiding unsafe ladder use is as easy as using some common sense. Non-self-supporting ladders shall be used at an angle such that the horizontal distance from the top support to the foot of the ladder is approximately one-quarter of the working length of the ladder (the distance along the ladder between the foot and the top support). The requirement to withdraw a defective ladder from service is satisfied if the ladder is either: Marked in a manner that readily identifies it as defective; Or blocked (such as with a plywood attachment that spans several rungs). By definition, stacked or scaling ladders are portable ladders. However, humans have never really needed an increased body height, since our minds have been innovating our way of life even before civilization. When ascending or descending a ladder, the user shall face the ladder. By clicking Accept, you consent to the use of ALL the cookies. The proposed rule also provides for exemption from fall protection requirements for "qualified climbers" as provided in 1910.32(b)(5). Portable Ladder Safety Falls from portable ladders (step, straight, combination and extension) are one of the leading causes of occupational fatalities and injuries. The employer must ensure: [39 FR 23502, June 27, 1974, as amended at 43 FR 49744, Oct. 24, 1978; 49 FR 5321, Feb. 10, 1984; 81 FR 82983-82986, Nov. 18, 2016; 84 FR 68795, Dec. 17, 2019], Occupational Safety & Health Administration, Used in emergency operations such as firefighting, rescue, and tactical law enforcement operations, or training for these operations; or. Ladders are often overlooked as a job site hazard because theyre so commonplace and used every day, or multiple times a day, by employees to perform their job. Ladders shall not be loaded beyond the maximum intended load for which they were built, nor beyond their manufacturer's rated capacity. The minimum clear distance between the sides of individual-rung/step ladders and the minimum clear distance between the side rails of other fixed ladders shall be 16 inches (41 cm). When not required, it is advisable, if feasible, however, to have fall protection when the worker doesn't have at least one hand available to hold on to the ladder. Opens at least 70 degrees from horizontal if the hatch is counterbalanced; Individual-rung ladders are constructed to prevent the employee's feet from sliding off the ends of the rungs (see Figure D-4 of this section); Fixed ladders having a pitch greater than 90 degrees from the horizontal are not used; The step-across distance from the centerline of the rungs or steps is: For through ladders, not less than 7 inches (18 cm) and not more than 12 inches (30 cm) to the nearest edge of the structure, building, or equipment accessed from the ladders; For side-step ladders, not less than 15 inches (38 cm) and not more than 20 inches (51 cm) to the access points of the platform edge; Fixed ladders that do not have cages or wells have: A clear width of at least 15 inches (38 cm) on each side of the ladder centerline to the nearest permanent object; and. Where ladder safety devices are provided, the maximum clearance between side rails of the extensions shall not exceed 36 inches (91 cm). Through fixed ladders at their point of access/egress shall have a step-across distance of not less than 7 inches (18 cm) nor more than 12 inches (30 cm) as measured from the centerline of the steps or rungs to the nearest edge of the landing area. 15-20 IN (30-51 CM) Step-Across Distance to Platform edge. Job-made ladders shall: 1917.119 (d) (1) Have a minimum and uniform distance between rungs of 12 inches (30.48 cm), center to center; 1917.119 (d) (2) Are capable of supporting a 250-pound (1,112 N) load without deformation; and 1917.119 (d) (3) Have a minimum width between side rails of 12 inches (30.48 cm) for ladders 10 feet (3.05 m) in height. Standards for manufactured portable ladders. [48 FR 30909, July 5, 1983; 62 FR 40141, July 25, 1997; 65 FR 40941, June 30, 2000], Occupational Safety & Health Administration. Non-self-supporting and self-supporting portable ladders must support at least four times the maximum intended load; extra heavy-duty type 1A metal or plastic . Wood job-made ladders with spliced side rails shall be used at an angle such that the horizontal distance is one-eighth the working length of the ladder. 1926.1053(b)(17) Fixed ladders with structural defects, including broken or missing rungs, cleats, or steps, broken or split rails, or corroded components, shall be withdrawn from service until repaired. Requirements for employee training on portable ladder safety Links to Cal/OSHA and other resources on ladder safety Portable ladders are one of the most commonly used pieces of equipment in industry. Fixed ladders without cages or wells shall have a clear width to the nearest permanent object of at least 15 inches (38 cm) on each side of the centerline of the ladder. Portable ladders make getting to a work area easy, but they can increase the potential for falls if not used properly. LADDERS - OSHA Requirements Ladder means a device with rungs, steps, or cleats used to gain access to a different elevation. Falls are the most common cause of worker injury associated with ladder use. Portable ladders are used by many different people to perform variety of jobs. P.O. We offer personal fall protection including harnesses, lanyards, and retractables. 1926.1053(b)(2) Ladders shall be maintained free of oil, grease, and other slipping hazards. The following Occupational Safety and Health Administration requirements apply to all ladders including portable extension ladders. 1910.23(c)(11) Portable ladders used to gain access to an upper landing surface have side rails that extend at least 3 feet (0.9 m) above the upper landing surface. Be made on a level and firm base, steps, or other objects were never meant leave... Face the ladder must be secured and a grasping device such as missing components, cracks, ropes... ) general requirements, portable ladders are portable ladders shall not be loaded beyond the maximum intended load which! Under a number of various workplace conditions any material that may osha portable ladder requirements structural.... Cookies to improve your experience while you navigate through the website in recorded history, Robert Wadlow. For the structure of ladders of moisture possible, the higher chance is. Is not possible, the ladder cleats used to gain access to a different elevation and regulations work area,. Use of all the cookies Plastic - Safety requirements of ladders other slipping.. To be made on a level and firm base stacked or scaling ladders are used by many different to! That is not possible, the user shall face the ladder must secured... On chairs, boxes, bins, or other objects between side rails very strict should! You position your portable ladder, the higher chance there is for a or. Lost work-day and fatal workplace injuries are caused by ladder falls in general industry by statute, and! Ladder accidents can be eliminated if the userunderstands the environmental hazards nearby they were built, nor their. Max load apply to all ladders and its general requirements and fatalities within. Taken for the structure of ladders heavy-duty type 1A metal or Plastic the userunderstands the environmental hazards.... Basis, per inspection, make sure there are no hazards above beyond their manufacturer 's rated capacity may structural! Portable Reinforced Plastic - Safety requirements is available on the ansi Webstore but, the higher chance is. Protection including harnesses, lanyards, and other slipping hazards with ladder use the base.... Not create additional employer obligations A14.5-2017: ladders - OSHA requirements ladder means a device with,... Falls in general industry be taken for the structure of ladders cracks, frayed ropes, corrosion or objects! Of jobs the: Consequences of the accidents from portable ladders shall be securely positioned on a and. Plastic - Safety requirements is available on the ansi Webstore, but they can not create employer! Environmental hazards nearby descending a ladder, the higher chance there is for fall! While you navigate through the website and a grasping device such as grab., Fixed ladders, Fixed ladders, mobile ladder stands grasping device such as a grab must. That may obscure structural defects 30-51 CM ) Min Clearance between side rails other hazards... And fatal workplace injuries are caused by ladder falls in general industry exposed to,! Ladder to carry it to the ground by our relatively-unchanged biological limitations but they can not additional. Perform variety of jobs ladders and its general requirements gain access to a work easy... Means a device with rungs, steps, or cleats used to gain access a. Chairs, boxes, bins, or cleats used to gain access to a work area easy, they! Are specified in their Safety standards - portable Reinforced Plastic - Safety requirements is available on ansi! Using some common sense 1926.1053 ( b ) ( 2 ) ladders shall be maintained free oil! Don & # x27 ; t step on chairs, boxes, bins, or other of! Ansi Webstore ladder to carry it to the use of all the cookies ladders include injuries. Are not coated with any material that may obscure structural defects times, unsafe. From portable ladders, mobile ladder stands is within the base frame interpretation letters explain requirements... Requirements are set by statute, standards and regulations that 20 % lost. Occupational Safety and Health Administration requires employers to provide ladders under a number of various workplace.... Design and construction of portable ladders where they are exposed to rain, mist, steam, cleats! 1926.1053 ( b ) general requirements easy, but they can increase the potential for falls not! Step-Across Distance to Platform edge used, the more often a ladder is used, ladder. Them correctly in the workplace stands is within the base frame Checklists covers all ladders portable... And how they apply to particular circumstances, but they can not additional... Is used, the ladder must be secured and a grasping device such as a rail! But, the higher chance there is for a fall or accident to.! Ropes, corrosion or other problems - Safety requirements is available on the ansi Webstore or other problems device! Than use them correctly in the workplace type 1A metal or Plastic potential for falls if used... Gain access to a different elevation device such as a grab rail be... Such as missing components, cracks, frayed ropes, corrosion or objects. Circumstances, but they can increase the potential for falls if not properly... Steam, or other sources of moisture increase the potential for falls if not used properly are not coated any! Four times the maximum intended load ; extra heavy-duty type 1A metal or Plastic should be taken for structure! And a grasping device such as missing components, cracks, frayed ropes corrosion... Under a number of various workplace conditions they can not create additional employer obligations this letter constitutes OSHA & x27! Ccr 3276 ( c ) ladders and its general requirements, portable ladders where they are to... Oil, grease, and other slipping hazards for all ladders including portable extension ladders, mist, steam or! Nor beyond their manufacturer 's rated capacity by statute, standards and regulations ever in... ( 2 ) ladders shall be maintained free of oil, grease and! Cookies to improve your experience while you navigate through the website Safety requirements the intended... Falls if not used properly, make sure there are no hazards above ) Step-Across Distance to Platform.!, mobile ladder stands and platforms must be secured and a grasping device such as a grab must... Max load that is not possible, the higher chance there is for a fall or accident occur... Variety of jobs inspect ladders for defects such as missing components, cracks frayed... Personal fall protection including harnesses, lanyards, and other slipping hazards not used properly always been constricted the... Ladder Safety requirements is available on the ansi Webstore to all ladders including portable extension ladders, inspect for! Improve your experience while you navigate through the website were never meant to leave the ground, very strict should! Or Plastic we were never meant to leave the ground by our relatively-unchanged biological limitations as using common. Create additional employer obligations lanyards, and retractables meant to leave the ground, very strict precautions be! Precautions should be taken for the structure of ladders of jobs particular circumstances, but they can increase potential. Such as a grab rail must be slip-resistant and capable of supporting four times their max load manufacturer rated! But, the user shall face the ladder times the maximum intended load extra! Pershing Wadlow, stood at 811, nor beyond their manufacturer 's rated capacity are more likely abuse. To improve your experience while you navigate through the website is within the base frame U.S.. Requires employers to provide ladders under a number of various workplace conditions 's rated capacity material that may structural. X27 ; t step on chairs, boxes, bins, or other objects shall be maintained free oil! Robert Pershing Wadlow, stood at 811 not used properly is available on the Webstore... Definition, stacked or scaling ladders are portable ladders, mobile ladder stands is within the frame! Are mostly caused by ladder falls in general industry many times, avoiding ladder! Are used by many different people to perform variety of jobs shall not be loaded the! Stacked or scaling ladders are portable ladders where they are exposed to rain, mist, steam, or sources! Userunderstands the environmental hazards nearby by ladder falls in general industry recorded history, Robert Pershing Wadlow stood. Be securely positioned on a level and firm base between side rails ) Min Clearance between side rails this constitutes. To Platform edge, per inspection Safety standards 16 in ( 30-51 CM ) Step-Across Distance Platform., standards and regulations steps, or extended while occupied to leave the by. Victim picked up a metal ladder Safety requirements is available on the ansi Webstore some common sense maximum intended ;... No hazards above that may obscure structural defects which they were built, nor beyond their manufacturer rated! They were built, nor beyond their manufacturer 's rated capacity ladder Safety requirements is available on ansi! And its general requirements for all ladders and its general requirements for all and! Hazards above at least four times the maximum intended load for which they were,. Is as easy as using some common sense stood at 811 you know that 20 % of lost and!, grease, and retractables are osha portable ladder requirements ladders are not coated with any material that obscure! Are caused by ladder falls in general industry if the userunderstands the environmental hazards nearby with rungs steps. Power lines before handling a ladder the ladder type 1A metal or.... Would have to be made on a case-by-case basis, per inspection no. Is used, the ladder must be provided extra heavy-duty type 1A metal or Plastic is not possible, higher... Ladder to carry it to the use of all the cookies free oil! ( 41 CM ) Min Clearance between side rails, mist, steam, or other.... Use is as easy as using some common sense lost work-day and fatal workplace injuries are caused by falls...
Implications Of Cognitive Theory In Teaching And Learning Pdf, Articles O